HELICOMMAND RIGID
| Manufacturer |  |
Reward Points  |
838 |
| Location | P11 |
World´s First - HeliCommand !
Flight attitude stabilisation and positioning system for model helicopters.
The breakthrough:
Many attempts have been made to create a stabilisation system for free-flying helicopters. The control aids familiar in the modelling world are either just additional x-y gyro systems, or simple light sensors which only work if the horizon is very flat, with no obstacles in the line of sight. Until now, regulatory systems offering genuine inherent stability have been enormously complex, due to the unavoidable fact that it is impossible in a helicopter to measure angles of inclination relative to gravity; the second problem is that of obtaining a stable geographic position; these problems could only be overcome if at least a GPS system was installed in the model. If you were piloting a conventional helicopter and left it to its own devices for a few seconds, it would quickly start to drift off in a random direction, at the same time constantly accelerating - in short, it would not survive for long.
The HeliCommand unit stabilises the geographical position of the model helicopter as well as its flight attitude. This involves a new technique of ground sensing which is much lighter and cheaper than GPS, and also works far more accurately when close to the ground: unwanted movements can be measured much more finely, and automatic compensation applied much more accurately. An additional advantage over GPS is that the system even works where the flying site is closely surrounded by buildings or trees, and even indoors, provided that the lighting and contrast conditions are adequate.
This completely new attitude stabilisation and positioning technology is now available to modellers for the first time. The HeliCommand incorporates several control and measuring systems, and provides a superb level of stabilisation.
Decisive features are a quality of regulation never obtained before, combined with compactness and light weight and a reasonable price.
Applications:
Technical features:
Integral functions:
Tail rotor gyro
The HeliCommand unit features an integral high-quality heading-hold gyro. Of course, a separate gyro can also be used if you prefer.
Auto-trim
Another important feature is automatic trim; a button-press on the transmitter automatically neutralises the three control axes: pitch, roll and tail. For auto-pilot operations the trim is only necessary during the first flight (after installation). However the trim can also be used for manual control. Any reasonably smooth phase of flight lasting a minimum of seven seconds is sufficient for the automatic trim system to define correct trim values. The settings are stored, but they can also be revised and corrected at any time.
Swashplate mixer
The HeliCommand unit incorporates a comprehensive integral swashplate mixer (H2, HR3, H4). This makes it possible to control all current types of helicopter using simple radio control systems (without swashplate mixers). In this case the display module or the PC adaptor and software is required in order to carry out adjustments. The mixer settings are entered using a new form of procedure which is very simple to operate; this saves the user the task of studying the menu system etc.
Pilot channel
The effect of the stabilising / positioning mode can be adjusted proportionally using a spare radio
control channel; it can also be switched off completely for 3-D flying.
The in-flight switchable gain system offers three different positions:
Fail-safe
High-quality fail-safe function with FM receivers. If the radio link fails, the fail-safe responds extremely quickly and almost continuously, setting the roll-axis and pitch-axis functions to neutral, whilst maintaining the collective pitch function at the last value.
Heli-Command works
Two independent instrument systems are used in conjunction with sophisticated software to ensure high reliability. The position measurement is based on a ground sensor which works on a similar principle to an optical computer mouse; the difference is that the position-finding continues to work at flight altitudes of around 3 m and more, even when daylight is beginning to fade. The movement sensor detects the ground while the helicopter is flying, and can be considered as a replacement for the eye of an airborne pilot. The sensor is able to detect all relative movement in the horizontal plane by analysing the contrasts exhibited by virtually every type of ground surface; this works just as accurately as a computer mouse on its base surface. The supplementary attitude stabilisation system contains three electronic gyros and works using an artificial horizon, i.e. it is entirely independently of the visual conditions. This arrangement enables the HeliCommand to stabilise the helicopter´s inclination relative to the horizontal plane, independently of lighting conditions (in contrast to previous types of stabiliser), and also to stabilise the machine´s position above the ground when in regulatory mode. Only in exceptional cases, e.g. in the dark, above stretches of water, or over a totally smooth covering of snow, is the optical sensing device unable to supply a signal; if this should occur, the remaining on- board instruments automatically assume the task of stabilising the helicopter. If brief, this "bridging" action is not noticeable. If it lasts longer, the helicopter will automatically switch from positioning mode to stabilising mode. The pilot will then detect this, and may have to compensate for any slow drift which occurs by giving a straightforward corrective control command. If particular ambient conditions make it obvious that the optical ground sensor cannot pick up adequate contrast (such as when flying indoors), the pilot would normally switch over to stabilisation mode (attitude regulation). However, these special features do not need to be taken into account if you limit yourself to normal weather and usual model flying conditions and environments.
The HeliCommand "Rigid-Stabi" is another version of the system:
In addition to all the functions of the Heli-Command 3D, this variant provides stabilisation for helicopters which are not fitted with a mechanical stabiliser bar (flybar). This applies, for example, to some scale machines and helicopters with multi-blade rotor heads. This special attitude-holding stabilisation reliably prevents the characteristic tendency of "flybar-less" rotor heads to balloon up abruptly.
Model helicopters with a rigid head are more agile, contain fewer parts and consume less motor power. The HeliCommand "Rigid" offers a broad field for experimentation in the future.
| Specification: | |
| Dimensions: 55x35x12.5 mm | |
| Mass/weight: 33.00 pond/g | |
| Operating voltage: 4.8-6 Volts |
Customers who bought this product also bought the following products:
HELICOMMAND 3D
Languages
 |  |  |  |  |  |
Shopping Cart
Stock Levels
In Stock
Small Quantity
Due in 1-2 Days
Out of Stock
